設備占地面積： 35×3.5×5（長×寬×高）米。

Equipment cover an area of an area: 35 * 3.5 * 5 meters (length x width x height).

設備進料方向：左進右出。

Equipment feed direction: left to right.

電壓參數380，50Hz，3相。

Voltage parameter 380, 50 Hz, 3 phase.

氣源：流量為0.5m3/分鐘；

Source: the flow of 0.5 m3 / min;

壓力為0-0.7MPa。

Pressure to 0-0.7 MPa.

液壓油：46#液壓油。

The hydraulic oil: 46 # hydraulic oil.

齒輪油：18#雙曲線齒輪油。

Gear oil: 18 # hyperbolic gear oil.

設備主要技術參數

Equipment main technical parameters

軋制帶鋼寬度：200—950 mm

Rolling steel strip width: 200-950 mm

軋制帶鋼厚度：0.6~2.0 mm

Rolling steel strip thickness: 0.6 ~ 2.0 mm

軋制帶鋼材質：Q235冷軋帶鋼

Rolling steel strip material: Q235 cold-rolled strip steel

在線沖孔、生產速度：2-6m/分鐘(根據產品長度及沖孔的數量決定）

online punching.production speed: 2-6 m/min (determined according to the length.the number of punching products)

主機成型速度：10-12m/分鐘

The host molding speed: 10 to 12 m/min

軋制工件長度：2000—12000 mm

Rolling workpiece length: 2000-12000 mm

電機防爆等級ExdIICT4

ExdIICT4 explosion-proof motor level

電機防護等級IP55

Motor protection grade IP55

設備裝機總?cè)萘浚杭s35KW。

Equipment installed gross capacity: about 35 kw.

軋制產品范圍

The product range of rolling

本沖壓成型機組可以軋制最大厚度為2.0mm槽盒式電纜橋架，產品寬度從100至600mm，高度從50至150mm之間不同規格的鋼質電纜橋架產品。

The stamping forming unit can be rolling thickness of 2.0 mm slot box type cable tray, products from 100 to 600 mm in width, height from 50 to 150 mm between different specifications of steel cable tray products.

供貨及服務范圍

The scope of supply.services

本條款規定了合同設備的供貨范圍（見表一），賣方保證所提供設備為全新的、先進的、成熟的、完整的和安全可靠的，且設備的技術性能、功能符合技術條件的要求。

The provisions of this clause of the contract equipment in the scope of supply (see chart 1), the seller guarantees that the equipment for new, advanced, mature.complete,.safe.reliable,.the equipment of the technical performance.function accord with the requirement of technical conditions.

賣方確保供貨范圍完整，以能滿足用戶安裝、運行要求為原則，在技術規范中涉及的供貨要求也作為本供貨范圍的補安裝、調試、運行中發現缺項由賣方補充。

The seller to ensure that the complete scope of supply, in order to meet the demand of users to install.run for the principle, supply requirements are also involved in the technical specification of the scope of supply for installation, debugging.operation of found missing items added by the seller.

成型工藝

Molding process

被動放料..校平..沖孔（沖連接孔）..切斷..成型.-出料

Passive feeding, leveling, punching rushed connection (hole) - cutting - forming - discharging